Ethernet (redirected from Xerox Ethernet)

Ethernet

Telecommunications networking protocol introduced by Xerox Corp. in 1979. It was developed as an inexpensive way of sending information quickly between office machines connected together in a single room or building, but it rapidly became a standard computer interconnection method. The original data rate of 10 megabits per second has been increased to 100 megabits per second for a new standard known as fast ethernet. The original specification required coaxial cable as the communications medium, but costs have been reduced through the employment of simple paired wires. See also computer network.

---

The standard local area network (LAN) access method. A reference to "LAN," "LAN connection" or "network card" automatically implies Ethernet. Defined by the IEEE as the 802.3 standard, Ethernet is used to connect computers in a company or home network as well as to connect a single computer to a cable modem or DSL modem for Internet access.

Most new computers come network ready with Ethernet built in. For machines without a network connection, Ethernet adapters can be added via USB or PC Card or by plugging an Ethernet card into a free PCI bus slot inside the case.

Megabits Per Second: 10, 100, 1,000 and 10,000
A 10/100 Ethernet port supports two speeds: 10 Mbps (10Base-T) and 100 Mbps (100Base-T). Computers also come with 10/100/1000 ports, which includes Gigabit Ethernet at 1 Gbps (1,000 megabits). Ethernet devices negotiate with each other and transmit at the highest speed possible. For high-speed backbones in metropolitan and wide area networks, 10 Gigabit Ethernet (10,000 megabits), the fastest Ethernet, is also used (see 10 Gigabit Ethernet).

Shared or Switched
Ethernet is wired in a star configuration with a hub or switch in the middle. Hubs, which predated switches, are shared media devices. All stations attached to the hub share the total bandwidth. Switches provide each sender and receiver pair with the full bandwidth and are significantly faster than hubs (see switched Ethernet). Like the client machines, Ethernet switches and hubs also support 10/100 and 10/100/1000 speeds.

Most Ethernets Use Twisted Pairs
Ethernet uses economical twisted pair cables and standard RJ-45 connectors (see cable categories). Sometimes, spare telephone wires in a building may be used, but often only at the lowest speed. To extend distances, fiber-optic cable is also used (see 100Base-T, Gigabit Ethernet and FOIRL). The first versions of Ethernet used coaxial cable (see 10Base5 and 10Base2).

Ethernet Frames
Ethernet transmits variable length frames from 72 to 1518 bytes in length, each containing a header with the addresses of the source and destination stations and a trailer that contains error correction data. Higher-level protocols, such as IP and IPX, fragment long messages into the frame size required by the Ethernet network being employed (see MTU).

Collision Detection
Ethernet uses the CSMA/CD technology to broadcast each frame onto the physical medium (wire, fiber, etc.). All stations attached to the Ethernet are "listening," and the station with the matching destination address accepts the frame and checks for errors. Ethernet is a data link protocol (MAC layer protocol) and functions at layers 1 and 2 of the OSI model.

History
Invented by Robert Metcalfe and David Boggs at Xerox PARC in 1973, Ethernet first ran at 2.94 Mbps. Metcalfe later joined Digital where he facilitated a joint venture between Digital, Intel and Xerox to collaborate further on Ethernet. Version 1 was finalized in 1980, and products shipped in the following year. In 1983, the IEEE approved the Ethernet 802.3 standard. See 100Base-T, Gigabit Ethernet, 10 Gigabit Ethernet and switched Ethernet.

 ETHERNET LIMITATIONS

                        Maximum            Maximum
 Type                   Segment length     Devices
 TWISTED PAIR (star topology)
  10Base-T               328 ft. (100 m)     1
  100Base-T              328 ft. (100 m)     1
  1000Base-T             328 ft. (100 m)     1

 COAX (bus topology)
  10Base5 "thick"       1640 ft. (500 m)   100
  10Base2 "thin"         607 ft. (185 m)    30

 FIBER (star topology)
  FOIRL                    .6 mi. (1 km)     1
  10Base-F                1.2 mi. (2 km)     1
  100Base-FX multimode    1.2 mi. (2 km)     1
  100Base-FX single-mode    6 mi. (10 km)    1

Twisted Pair Ethernet

Most Ethernets use twisted pair wiring. All cables use RJ-45 connectors between the network adapters in the PC and a central hub or switch.

Ethernet Switch

This 10/100 switch from Omnitron has 16 ports and automatically senses the transmission rate of the line and adjusts accordingly.

The Original Ethernet

The first Ethernet (10Base5) used a bus topology and a thick coaxial cable. Transceivers connect the network adapters to the cable via a vampire tap that "bites" into the coax.

Thin Ethernet

10Base2 Ethernet was a later variation of the original 10Base5. It used a thinner coaxial cable attached to each node using BNC T-connectors.

---

(networking)

Ethernet - A local area network first described by Metcalfe & Boggs of Xerox PARC in 1976. Specified by DEC, Intel and XEROX (DIX) as IEEE 802.3 and now recognised as the industry standard. Data is broken into packets and each one is transmitted using the CSMA/CD algorithm until it arrives at the destination without colliding with any other packet. The first contention slot after a transmission is reserved for an acknowledge packet. A node is either transmitting or receiving at any instant. The bandwidth is about 10 Mbit/s. Disk-Ethernet-Disk transfer rate with TCP/IP is typically 30 kilobyte per second. Version 2 specifies that collision detect of the transceiver must be activated during the inter-packet gap and that when transmission finishes, the differential transmit lines are driven to 0V (half step). It also specifies some network management functions such as reporting collisions, retries and deferrals. Ethernet cables are classified as "XbaseY", e.g. 10base5, where X is the data rate in Mbps, "base" means "baseband" (as opposed to radio frequency) and Y is the category of cabling. The original cable was 10base5 ("full spec"), others are 10base2 ("thinnet") and 10baseT ("twisted pair") which is now (1998) very common. 100baseT ("Fast Ethernet") is also increasingly common. Usenet newsgroup: news:comp.dcom.lans.ethernet. http://wwwhost.ots.utexas.edu/ethernet/ethernet-home.html.