..... Click the link for more information. ; insulation insulation (ĭn'səlā`shən, ĭn'sy
..... Click the link for more information. ). At high temperatures its conductivity approaches that of a metal, and at low temperatures it acts as an insulator. In a semiconductor there is a limited movement of electrons, depending upon the crystal structure of the material used. The substances first used for semiconductors were the elements germanium, silicon, and gray tin. It was found that the incorporation of certain impurities in them enhances their conductive properties. The impurities either add free electrons or create holes (electron deficiencies) in the crystal structures of the host substances by attracting electrons. Thus there are two types of semiconductor: the N-type (negative), in which the current carriers (electrons) are negative, and the P-type (positive), in which the positively charged holes move and carry the current. The process of adding these impurities is called doping; the impurities themselves are called dopants. Dopants that contribute mobile electrons are called donor impurities; those that cause holes to form are acceptor impurities. Undoped semiconductor material is called intrinsic semiconductor material. Certain chemical compounds, including gallium arsenide, indium antimonide, and aluminum phosphide are semiconductors. Semiconductors are used to produce such electronic devices as diodes diode (dī`ōd), two-terminal electronic device that permits current flow predominantly in only one direction.
..... Click the link for more information. , transistors transistor, three-terminal, solid-state electronic device used for amplification and switching. It is the solid-state analog to the triode electron tube ; the transistor has replaced the electron tube for virtually all common applications.
..... Click the link for more information. , and computer memory devices. The field of solid-state physics solid-state physics, study of the properties of bulk matter rather than those of the individual particles that compose it. Solid-state physics is concerned with the properties exhibited by atoms and molecules because of their association and regular, periodic
..... Click the link for more information. includes the study of semiconductors. See also integrated circuit integrated circuit (IC), electronic circuit built on a semiconductor substrate, usually one of single-crystal silicon. The circuit, often called a chip, is packaged in a hermetically sealed case or a nonhermetic plastic capsule, with leads extending from it for
..... Click the link for more information. .
semiconductor
Class of crystalline solids with electrical conductivity between that of a conductor and an insulator. Such materials can be treated chemically to allow transmission and control of an electric current. Semiconductors are used in the manufacture of electronic devices such as diodes, transistors, and integrated circuits. Intrinsic semiconductors have a high degree of chemical purity, but their conductivity is poor. Extrinsic semiconductors contain impurities that produce much greater conductivity. Some common intrinsic semiconductors are single crystals of silicon, germanium, and gallium arsenide; such materials can be converted into the technologically more important extrinsic semiconductors by addition of small amounts of impurities, a process called doping (see dopant). Advances in semiconductor technology in recent years have gone hand in hand with increased operational speed in computers.
semiconductor
A solid state material that can be electrically altered. Certain elements in nature, such as silicon, perform like semiconductors when chemically combined with other elements. Various optical materials can also change their state (see phase change disc).
When electricity or light is applied to semiconductors, they change their state between conductive and non-conductive or reflective and non-reflective. The most significant semiconductor is the transistor, which in digital circuits works like an on/off switch. For analog applications, it may be an on/off switch as well, but is more likely used as an amplifier, taking in a low-voltage signal and outputting a higher voltage. See n-type silicon, doping and chip.
 |
| Conceptual View of a Transistor |
|---|
| In a certain type of transistor, the semiconductor material normally acts as an insulator. When it is pulsed with electricity, it becomes electrically conductive for that moment and acts like an electrical bridge. |
semiconductor
semiconductor [¦sem·i·kən¦dək·tər]
Semiconductor
A solid crystalline material whose electrical conductivity is intermediate between that of a metal and an insulator. Semiconductors exhibit conduction properties that may be temperature-dependent, permitting their use as thermistors (temperature-dependent resistors), or voltage-dependent, as in varistors. By making suitable contacts to a semiconductor or by making the material suitably inhomogeneous, electrical rectification and amplification can be obtained. Semiconductor devices, rectifiers, and transistors have replaced vacuum tubes almost completely in low-power electronics, making it possible to save volume and power consumption by orders of magnitude. In the form of integrated circuits, they are vital for complicated systems. The optical properties of a semiconductor are important for the understanding and application of the material. Photodiodes, photoconductive detectors of radiation, injection lasers, light-emitting diodes, solar-energy conversion cells, and so forth are examples of the wide variety of optoelectronic devices. See Laser, Light-emitting diode, Semiconductor diode, Thermistor, Transistor
Conduction in semiconductors
The electrical conductivity of semiconductors ranges from about 103 to 10-9 ohm-1 cm-1, as compared with a maximum conductivity of 107 for good conductors and a minimum conductivity of 10-17 ohm-1 cm-1 for good insulators. See Electric insulator
The electric current is usually due only to the motion of electrons, although under some conditions, such as very high temperatures, the motion of ions may be important. The basic distinction between conduction in metals and in semiconductors is made by considering the energy bands occupied by the conduction electrons. See Band theory of solids, Ionic crystals
At absolute zero temperature, the electrons occupy the lowest possible energy levels, with the restriction that at most two electrons with opposite spin may be in the same energy level. In semiconductors and insulators, there are just enough electrons to fill completely a number of energy bands, leaving the rest of the energy bands empty. The highest filled energy band is called the valence band. The next higher band, which is empty at absolute zero temperature, is called the conduction band. The conduction band is separated from the valence band by an energy gap, which is an important characteristic of the semiconductor. In metals, the highest energy band that is occupied by the electrons is only partially filled. This condition exists either because the number of electrons is not just right to fill an integral number of energy bands or because the highest occupied energy band overlaps the next higher band without an intervening energy gap. The electrons in a partially filled band may acquire a small amount of energy from an applied electric field by going to the higher levels in the same band. The electrons are accelerated in a direction opposite to the field and thereby constitute an electric current. In semiconductors and insulators, the electrons are found only in completely filled bands at low temperatures. In order to increase the energy of the electrons, it is necessary to raise electrons from the valence band to the conduction band across the energy gap. The electric fields normally encountered are not large enough to accomplish this with appreciable probability. At sufficiently high temperatures, depending on the magnitude of the energy gap, a significant number of valence electrons gain enough energy thermally to be raised to the conduction band. These electrons in an unfilled band can easily participate in conduction. Furthermore, there is now a corresponding number of vacancies in the electron population of the valence band. These vacancies, or holes as they are called, have the effect of carriers of positive charge, by means of which the valence band makes a contribution to the conduction of the crystal. See Hole states in solids
The type of charge carrier, electron or hole, that is in largest concentration in a material is sometimes called the majority carrier and the type in smallest concentration the minority carrier. The majority carriers are primarily responsible for the conduction properties of the material. Although the minority carriers play a minor role in electrical conductivity, they can be important in rectification and transistor actions in a semiconductor.
Intrinsic semiconductors
A semiconductor in which the concentration of charge carriers is characteristic of the material itself rather than of the content of impurities and structural defects of the crystal is called an intrinsic semiconductor. Electrons in the conduction band and holes in the valence band are created by thermal excitation of electrons from the valence to the conduction band. Thus an intrinsic semiconductor has equal concentrations of electrons and holes. The carrier concentration, and hence the conductivity, is very sensitive to temperature and depends strongly on the energy gap. The energy gap ranges from a fraction of 1 eV to several electronvolts. A material must have a large energy gap to be an insulator.
Extrinsic semiconductors
Typical semiconductor crystals such as germanium and silicon are formed by an ordered bonding of the individual atoms to form the crystal structure. The bonding is attributed to the valence electrons which pair up with valence electrons of adjacent atoms to form so-called shared pair or covalent bonds. These materials are all of the quadrivalent type; that is, each atom contains four valence electrons, all of which are used in forming the crystal bonds. See Crystal structure
Atoms having a valence of +3 or +5 can be added to a pure or intrinsic semiconductor material with the result that the +3 atoms will give rise to an unsatisfied bond with one of the valence electrons of the semiconductor atoms, and +5 atoms will result in an extra or free electron that is not required in the bond structure. Electrically, the +3 impurities add holes and the +5 impurities add electrons. They are called acceptor and donor impurities, respectively. Typical valence +3 impurities used are boron, aluminum, indium, and gallium. Valence +5 impurities used are arsenic, antimony, and phosphorus.
Semiconductor material “doped” or “poisoned” by valence +3 acceptor impurities is termed p-type, whereas material doped by valence +5 donor material is termed n-type. The names are derived from the fact that the holes introduced are considered to carry positive charges and the electrons negative charges. The number of electrons in the energy bands of the crystal is increased by the presence of donor impurities and decreased by the presence of acceptor impurities. See Acceptor atom, Donor atom
At sufficiently high temperatures, the intrinsic carrier concentration becomes so large that the effect of a fixed amount of impurity atoms in the crystal is comparatively small and the semiconductor becomes intrinsic. When the carrier concentration is predominantly determined by the impurity content, the conduction of the material is said to be extrinsic. Physical defects in the crystal structure may have similar effects as donor or acceptor impurities. They can also give rise to extrinsic conductivity.
Materials
The group of chemical elements which are semiconductors includes germanium, silicon, gray (crystalline) tin, selenium, tellurium, and boron. Germanium, silicon, and gray tin belong to group 14 of the periodic table and have crystal structures similar to that of diamond. Germanium and silicon are two of the best-known semiconductors. They are used extensively in devices such as rectifiers and transistors.
A large number of compounds are known to be semiconductors. A group of semiconducting compounds of the simple type AB consists of elements from columns symmetrically placed with respect to column 14 of the periodic table. Indium antimonide (InSb), cadmium telluride (CdTe), and silver iodide (AgI) are examples of III–V, II–IV, and I–VI compounds, respectively. The various III–V compounds are being studied extensively, and many practical applications have been found for these materials. Some of these compounds have the highest carrier mobilities known for semiconductors. The compounds have zincblende crystal structure which is geometrically similar to the diamond structure possessed by the elemental semiconductors, germanium and silicon, of column 14, except that the four nearest neighbors of each atom are atoms of the other kind. The II–VI compounds, zinc sulfide (ZnS) and cadmium sulfide (CdS), are used in photoconductive devices. Zinc sulfide is also used as a luminescent material. See Luminescence, Photocon-ductivity
The properties of semiconductors are extremely sensitive to the presence of impurities. It is therefore desirable to start with the purest available materials and to introduce a controlled amount of the desired impurity. The zone-refining method is often used for further purification of obtainable materials. The floating zone technique can be used, if feasible, to prevent any contamination of molten material by contact with the crucible.
For basic studies as well as for many practical applications, it is desirable to use single crystals. Various methods are used for growing crystals of different materials. For many semiconductors, including germanium, silicon, and the III–V compounds, the Czochralski method is commonly used. The method of condensation from the vapor phase is used to grow crystals of a number of semiconductors, for instance, selenium and zinc sulfide. See Crystal growth
The introduction of impurities, or doping, can be accomplished by simply adding the desired quantity to the melt from which the crystal is grown. When the amount to be added is very small, a preliminary ingot is often made with a larger content of the doping agent; a small slice of the ingot is then used to dope the next melt accurately. Impurities which have large diffusion constants in the material can be introduced directly by holding the solid material at an elevated temperature while this material is in contact with the doping agent in the solid or the vapor phase.
A doping technique, ion implantation, has been developed and used extensively. The impurity is introduced into a layer of semiconductor by causing a controlled dose of highly accelerated impurity ions to impinge on the semiconductor.
An important subject of scientific and technological interest is amorphous semiconductors. In an amorphous substance the atomic arrangement has some short-range but no long-range order. The representative amorphous semiconductors are selenium, germanium, and silicon in their amorphous states, and arsenic and germanium chalcogenides, including such ternary systems as Ge-As-Te. Some amorphous semiconductors can be prepared by a suitable quenching procedure from the melt. Amorphous films can be obtained by vapor deposition.
Rectification in semiconductors
In semiconductors, narrow layers can be produced which have abnormally high resistances. The resistance of such a layer is nonohmic; it may depend on the direction of current, thus giving rise to rectification. Rectification can also be obtained by putting a thin layer of semiconductor or insulator material between two conductors of different material.
A narrow region in a semiconductor which has an abnormally high resistance is called a barrier layer. A barrier may exist at the contact of the semiconductor with another material, at a crystal boundary in the semiconductor, or at a free surface of the semiconductor. In the bulk of a semiconductor, even in a single crystal, barriers may be found as the result of a nonuniform distribution of impurities. The thickness of a barrier layer is small, usually 10-3 to 10-5 cm.
A barrier is usually associated with the existence of a space charge. In an intrinsic semiconductor, a region is electrically neutral if the concentration n of conduction electrons is equal to the concentration p of holes. Any deviation in the balance gives a space charge equal to e(p - n), where e is the charge on an electron. In an extrinsic semiconductor, ionized donor atoms give a positive space charge and ionized acceptor atoms give a negative space charge.
Surface electronics
The surface of a semiconductor plays an important role technologically, for example, in field-effect transistors and charge-coupled devices. Also, it presents an interesting case of two-dimensional systems where the electric field in the surface layer is strong enough to produce a potential wall which is narrower than the wavelengths of charge carriers. In such a case, the electronic energy levels are grouped into subbands, each of which corresponds to a quantized motion normal to the surface, with a continuum for motion parallel to the surface. Consequently, various properties cannot be trivially deduced from those of the bulk semiconductor. See Surface physics
Semiconductor
A solid crystalline material whose electrical conductivity is intermediate between that of a metal and an insulator. Semiconductors exhibit conduction properties that may be temperature-dependent, permitting their use as thermistors (temperature-dependent resistors), or voltage-dependent, as in varistors. By making suitable contacts to a semiconductor or by making the material suitably inhomogeneous, electrical rectification and amplification can be obtained. Semiconductor devices, rectifiers, and transistors have replaced vacuum tubes almost completely in low-power electronics, making it possible to save volume and power consumption by orders of magnitude. In the form of integrated circuits, they are vital for complicated systems. The optical properties of a semiconductor are important for the understanding and the application of the material. Photodiodes, photoconductive detectors of radiation, injection lasers, light-emitting diodes, solar-energy conversion cells, and so forth are examples of the wide variety of optoelectronic devices. See Integrated circuits, Laser, Light-emitting diode, Photoelectric devices, Semiconductor rectifier, Thermistor, Transistor, Varistor
Conduction in semiconductors
The electrical conductivity of semiconductors ranges from about 103 to 10-9 ohm-1 cm-1, as compared with a maximum conductivity of 107 for good conductors and a minimum conductivity of 10-17 ohm-1 cm-1 for good insulators.
The electric current is usually due only to the motion of electrons, although under some conditions, such as very high temperatures, the motion of ions may be important. The basic distinction between conduction in metals and in semiconductors is made by considering the energy bands occupied by the conduction electrons.
At absolute zero temperature, the electrons occupy the lowest possible energy levels, with the restriction that at most two electrons with opposite spin may be in the same energy level. In semiconductors and insulators, there are just enough electrons to fill completely a number of energy bands, leaving the rest of the energy bands empty. The highest filled energy band is called the valence band. The next higher band, which is empty at absolute zero temperature, is called the conduction band. The conduction band is separated from the valence band by an energy gap, which is an important characteristic of the semiconductor. In metals, the highest energy band that is occupied by the electrons is only partially filled. This condition exists either because the number of electrons is not just right to fill an integral number of energy bands or because the highest occupied energy band overlaps the next higher band without an intervening energy gap. The electrons in a partially filled band may acquire a small amount of energy from an applied electric field by going to the higher levels in the same band. The electrons are accelerated in a direction opposite to the field and thereby constitute an electric current. In semiconductors and insulators, the electrons are found only in completely filled bands, at low temperatures. In order to increase the energy of the electrons, it is necessary to raise electrons from the valence band to the conduction band across the energy gap. The electric fields normally encountered are not large enough to accomplish this with appreciable probability. At sufficiently high temperatures, depending on the magnitude of the energy gap, a significant number of valence electrons gain enough energy thermally to be raised to the conduction band. These electrons in an unfilled band can easily participate in conduction. Furthermore, there is now a corresponding number of vacancies in the electron population of the valence band. These vacancies, or holes as they are called, have the effect of carriers of positive charge, by means of which the valence band makes a contribution to the conduction of the crystal.
The type of charge carrier, electron or hole, that is in largest concentration in a material is sometimes called the majority carrier and the type in smallest concentration the minority carrier. The majority carriers are primarily responsible for the conduction properties of the material. Although the minority carriers play a minor role in electrical conductivity, they can be important in rectification and transistor actions in a semiconductor.
Intrinsic semiconductors
A semiconductor in which the concentration of charge carriers is characteristic of the material itself rather than of the content of impurities and structural defects of the crystal is called an intrinsic semiconductor. Electrons in the conduction band and holes in the valence band are created by thermal excitation of electrons from the valence to the conduction band. Thus an intrinsic semiconductor has equal concentrations of electrons and holes. The carrier concentration, and hence the conductivity, is very sensitive to temperature and depends strongly on the energy gap. The energy gap ranges from a fraction of 1 eV to several electronvolts. A material must have a large energy gap to be an insulator.
Extrinsic semiconductors
Typical semiconductor crystals such as germanium and silicon are formed by an ordered bonding of the individual atoms to form the crystal structure. The bonding is attributed to the valence electrons which pair up with valence electrons of adjacent atoms to form so-called shared pair or covalent bonds. These materials are all of the quadrivalent type; that is, each atom contains four valence electrons, all of which are used in forming the crystal bonds.
Atoms having a valence of +3 or +5 can be added to a pure or intrinsic semiconductor material with the result that the +3 atoms will give rise to an unsatisfied bond with one of the valence electrons of the semiconductor atoms, and +5 atoms will result in an extra or free electron that is not required in the bond structure. Electrically, the +3 impurities add holes and the +5 impurities add electrons. They are called acceptor and donor impurities, respectively. Typical valence +3 impurities used are boron, aluminum, indium, and gallium. Valence +5 impurities used are arsenic, antimony, and phosphorus.
Semiconductor material “doped” or “poisoned” by valence +3 acceptor impurities is termed p‐type, whereas material doped by valence +5 donor material is termed n-type. The names are derived from the fact that the holes introduced are considered to carry positive charges and the electrons negative charges. The number of electrons in the energy bands of the crystal is increased by the presence of donor impurities and decreased by the presence of acceptor impurities.
At sufficiently high temperatures, the intrinsic carrier concentration becomes so large that the effect of a fixed amount of impurity atoms in the crystal is comparatively small and the semiconductor becomes intrinsic. When the carrier concentration is predominantly determined by the impurity content, the conduction of the material is said to be extrinsic. Physical defects in the crystal structure may have similar effects as donor or acceptor impurities. They can also give rise to extrinsic conductivity.
Materials
The group of chemical elements which are semiconductors includes germanium, silicon, gray (crystalline) tin, selenium, tellurium, and boron. Germanium, silicon, and gray tin belong to group 14 of the periodic table and have crystal structures similar to that of diamond. Germanium and silicon are two of the best-known semiconductors. They are used extensively in devices such as rectifiers and transistors.
A large number of compounds are known to be semiconductors. A group of semiconducting compounds of the simple type AB consists of elements from columns symmetrically placed with respect to column 14 of the periodic table. Indium antimonide (InSb), cadmium telluride (CdTe), and silver iodide (AgI) are examples of III–V, II–IV, and I–VI compounds, respectively. The various III–V compounds are being studied extensively, and many practical applications have been found for these materials. Some of these compounds have the highest carrier mobilities known for semiconductors. The compounds have zincblende crystal structure which is geometrically similar to the diamond structure possessed by the elemental semiconductors, germanium and silicon, of column 14, except that the four nearest neighbors of each atom are atoms of the other kind. The II–VI compounds, zinc sulfide (ZnS) and cadmium sulfide (CdS), are used in photoconductive devices. Zinc sulfide is also used as a luminescent material.
The properties of semiconductors are extremely sensitive to the presence of impurities. It is therefore desirable to start with the purest available materials and to introduce a controlled amount of the desired impurity. The zone-refining method is often used for further purification of obtainable materials. The floating zone technique can be used, if feasible, to prevent any contamination of molten material by contact with the crucible. See Zone refining
For basic studies as well as for many practical applications, it is desirable to use single crystals. Various methods are used for growing crystals of different materials. For many semiconductors, including germanium, silicon, and the III–V compounds, the Czochralski method is commonly used. The method of condensation from the vapor phase is used to grow crystals of a number of semiconductors, for instance, selenium and zinc sulfide.
The introduction of impurities, or doping, can be accomplished by simply adding the desired quantity to the melt from which the crystal is grown. When the amount to be added is very small, a preliminary ingot is often made with a larger content of the doping agent; a small slice of the ingot is then used to dope the next melt accurately. Impurities which have large diffusion constants in the material can be introduced directly by holding the solid material at an elevated temperature while this material is in contact with the doping agent in the solid or the vapor phase.
A doping technique, ion implantation, has been developed and used extensively. The impurity is introduced into a layer of semiconductor by causing a controlled dose of highly accelerated impurity ions to impinge on the semiconductor. See Ion implantation
An important subject of scientific and technological interest is amorphous semiconductors. In an amorphous substance the atomic arrangement has some short-range but no long-range order. The representative amorphous semiconductors are selenium, germanium, and silicon in their amorphous states, and arsenic and germanium chalcogenides, including such ternary systems as Ge-As-Te. Some amorphous semiconductors can be prepared by a suitable quenching procedure from the melt. Amorphous films can be obtained by vapor deposition.
Rectification in semiconductors
In semiconductors, narrow layers can be produced which have abnormally high resistances. The resistance of such a layer is nonohmic; it may depend on the direction of current, thus giving rise to rectification. Rectification can also be obtained by putting a thin layer of semiconductor or insulator material between two conductors of different material.
A narrow region in a semiconductor which has an abnormally high resistance is called a barrier layer. A barrier may exist at the contact of the semiconductor with another material, at a crystal boundary in the semiconductor, or at a free surface of the semiconductor. In the bulk of a semiconductor, even in a single crystal, barriers may be found as the result of a nonuniform distribution of impurities. The thickness of a barrier layer is small, usually 10-3 to 10-5 cm.
A barrier is usually associated with the existence of a space charge. In an intrinsic semiconductor, a region is electrically neutral if the concentration n of conduction electrons is equal to the concentration p of holes. Any deviation in the balance gives a space charge equal to e(p - n), where e is the charge on an electron. In an extrinsic semiconductor, ionized donor atoms give a positive space charge and ionized acceptor atoms give a negative space charge.
Surface electronics
The surface of a semiconductor plays an important role technologically, for example, in field-effect transistors and charge-coupled devices. Also, it presents an interesting case of two-dimensional systems where the electric field in the surface layer is strong enough to produce a potential wall which is narrower than the wavelengths of charge carriers. In such a case, the electronic energy levels are grouped into subbands, each of which corresponds to a quantized motion normal to the surface, with a continuum for motion parallel to the surface. Consequently, various properties cannot be trivially deduced from those of the bulk semiconductor. See Charge-coupled devices
| (electronics) | semiconductor - A material, typically crystaline, which allows
current to flow under certain circumstances. Common
semiconductors are silicon, germanium, gallium arsenide.
Semiconductors are used to make diodes, transistors and
other basic "solid state" electronic components. As crystals of these materials are grown, they are "doped" with traces of other elements called donors or acceptors to make regions which are n- or p-type respectively for the electron model or p- or n-type under the hole model. Where n and p type regions adjoin, a junction is formed which will pass current in one direction (from p to n) but not the other, giving a diode. One model of semiconductor behaviour describes the doping elements as having either free electrons or holes dangling at the points in the crystal lattice where the doping elements replace one of the atoms of the foundation material. When external electrons are applied to n-type material (which already has free electrons present) the repulsive force of like charges causes the free electrons to migrate toward the junction, where they are attracted to the holes in the p-type material. Thus the junction conducts current. In contrast, when external electrons are applied to p-type material, the attraction of unlike charges causes the holes to migrate away from the junction and toward the source of external electrons. The junction thus becomes "depleted" of its charge carriers and is non-conducting. |
How to thank TFD for its existence? Tell a friend about us, add a link to this page, add the site to iGoogle, or visit webmaster's page for free fun content.
| ?Page tools | ||
|---|---|---|
|