Induction Motor

(redirected from AC induction motor)
Also found in: Dictionary, Acronyms.

induction motor

[in′dək·shən ‚mōd·ər]
(electricity)
An alternating-current motor in which a primary winding on one member (usually the stator) is connected to the power source, and a secondary winding on the other member (usually the rotor) carries only current induced by the magnetic field of the primary.
McGraw-Hill Dictionary of Scientific & Technical Terms, 6E, Copyright © 2003 by The McGraw-Hill Companies, Inc.
The following article is from The Great Soviet Encyclopedia (1979). It might be outdated or ideologically biased.

Induction Motor

 

an electrical asynchronous machine for converting electrical energy into mechanical. It operates on the principle of an interaction between a rotating magnetic field, resulting from the passage of three-phase alternating current through windings on the stator, and the current induced by the stator in windings on the rotor. The interaction develops mechanical forces which make the rotor turn in the direction of rotation of the magnetic field, provided that the rate of rotation for the rotor n is less than the rate of rotation of the field n1. Thus the rotor performs asynchronous rotation with respect to the field.

The phenomenon called magnetism of rotation was first demonstrated by the French physicist D.-F.-J. Arago (1824). He showed that a copper disk fastened to a vertical axis begins to rotate if a permanent magnet is rotated above it. Fifty-five years later, on June 28, 1879, the English scientist W. Bailey obtained a rotating magnetic field by successively connecting the windings of four bar electromagnets to a direct current source. In articles by M. Deprez (France, 1880–1883), E. Thomson (USA, 1887), and others, devices are described which are also based on the properties of a rotating magnetic field. However, an accurate scientific exposition of this phenomenon was given for the first time, almost simultaneously and independently of each other, in 1888 by the Italian physicist G. Ferraris and the Croatian engineer and scientist N. Tesla.

The two-phase induction motor was invented by N. Tesla in 1887 (English patent no. 6,481), and he reported it publicly in 1888. This type of induction motor did not become popular, mainly because of the poor starting characteristics. In 1889, M. O. Dolivo-Dobrovol’skii designed and tested the world’s first three-phase induction motor in which a “squirrel-cage” type of rotor was used (German patent no. 51,083), and the stator winding was placed in slots around the entire periphery of the stator. In 1890, Dolivo-Dobrovol’skii invented the phase-wound rotor, with slip rings and starting devices (English patent no. 20,425 and German patent no. 75,361). After two years he proposed a rotor design known as the “double squirrel cage” which, however, was used extensively only after 1898 thanks to the work of the French engineer P. Boucherot, who introduced an induction motor with a rotor like the motor with special starting characteristics.

The structural design of induction motors, their power, and their dimensions depend on the purpose and operating conditions. For example, there are motors with air and water cooling (general application); hermetically sealed, oil-Med (for electrodrills) and explosion-proof motors (for use in mines, dangerously explosive locations, and the like); dust-proof and spray-proof types (for use under marine conditions and in a tropical climate); and so forth. Some types of induction motors (such as servomotors for servo systems, circuits in automation and telemechanics with graded control of speed, and others) are developed and manufactured complete with control units, starter-protection apparatus, and built-in reduction gears. By comparison with single-phase induction motors the three-phase type has better starting and operating characteristics. The principal structural elements are a stator (the immovable part) and a rotor (the rotating part). According to the design of the rotor winding, induction motors are divided into wound-rotor and squirrel-cage motors. The air gap between stator and rotor is made as small as possible (down to 0.25 mm). The rotation rate of the rotor is a function of the rotation rate for the magnetic field of the stator, which is controlled by the power frequency and the number of pole pairs.

When a squirrel-cage induction motor is started, the starting current is between four and seven times greater than the nominal value. Therefore, direct connection to the power line is only used for motors up to a 200 kW power rating. The more powerful squirrel-cage induction motors are connected at first to a lower voltage so that the starting current is reduced by a factor of three or four. For the same reason, use is made of an autotransformer which is switched in series with the stator winding during starting. The starting current of phase-wound motors is limited by means of a starting resistance in the rotor circuit which is gradually reduced as the rotor picks up speed. After the start the rotor winding is short-circuited. In order to reduce frictional losses and brush wear, the brushes are usually raised by a brush-lifting mechanism which short-circuits the rotor winding beforehand through a ring.

The rotation rate of an induction motor is controlled primarily by a change in the number of pole pairs, by the resistance connected in the rotor circuit, by variation in the power supply frequency, and also by a cascade connection of several machines. The direction of rotation can be altered by changing over any two phases of the stator windings.

Because it is simple to manufacture and reliable to operate, the induction motor is widely employed in electric drives. Its chief drawbacks are the limited speed control range and the substantial reactive power drain under low load conditions. The creation of static, controlled, semiconductor frequency converters substantially broadens the field of application for induction motors in automatically controlled electric drives.

REFERENCES

Veselovskii, O. N. Mikhail Osipovich Dolivo-Dobrovol’skii. Moscow-Leningrad, 1958.
Kostenko, M. P., and L. M. Piotrovskii. Elektricheskie mashiny. Moscow-Leningrad, 1958. Chapters 1–2.

M. G. CHILIKIN

The Great Soviet Encyclopedia, 3rd Edition (1970-1979). © 2010 The Gale Group, Inc. All rights reserved.

Induction motor

An alternating-current motor in which the currents in the secondary winding (usually the rotor) are created solely by induction. These currents result from voltages induced in the secondary by the magnetic field of the primary winding (usually the stator). An induction motor operates slightly below synchronous speed and is sometimes called an asynchronous (meaning not synchronous) motor.

Induction motors are the most common electric motors due to their simple construction, efficiency, good speed regulation, and low cost. Polyphase induction motors come in all sizes and find wide use where polyphase power is available. Single-phase induction motors are found mainly in fractional-horsepower (1 horsepower = 746 W) sizes, and those up to 25 hp are used where only single-phase power is available.

There are two principal types of polyphase induction motors: squirrel-cage and wound-rotor machines. The difference in these machines is in the construction of the rotor. The stator construction is the same and is also identical to the stator of a synchronous motor. Both squirrel-cage and wound-rotor machines can be designed for two- or three-phase current.

Single-phase induction motors display poorer operating characteristics than polyphase machines, but are used where polyphase voltages are not available. They are most common in small sizes (½ hp or less) in domestic and industrial applications. Their particular disadvantages are low power factor, low efficiency, and the need for special starting devices.

McGraw-Hill Concise Encyclopedia of Engineering. © 2002 by The McGraw-Hill Companies, Inc.

induction motor

An alternating-current motor having its primary winding, on one member (which is usually the stator), connected to the source of electric power; a secondary winding on the other member (usually the rotor) carries the induced current.
McGraw-Hill Dictionary of Architecture and Construction. Copyright © 2003 by McGraw-Hill Companies, Inc.
References in periodicals archive ?
The speed of pump drive AC induction motor and, consequently, the water pressure in the water supply system is controlled by the variation of frequency of voltage provided by the frequency converter.
DC permanent magnet and AC induction motors drive equipment that runs all the time, like traditional conveyor;
The package consists of a brushless dc motor and speed control unit for 10, 25, 40, and 90 W output power, and the motor is less than half the size of an equivalent ac induction motor, with lengths of 1.65 in.
Long an industry staple, "The ac induction motor, until recently, was a fixed speed machine," Hendershot said.
DC injection braking involves applying DC voltage to the AC induction motor's stator winding.
Servomotors can be of three types: conventional DC motor, AC servomotor, or AC induction motor. Of the three motor types, the most commonly used is the AC servomotor, because of its superior performance advantages.
The new design combines an AC induction motor with a variable speed drive (inverter) mounted on the motor in a terminal box.
"Digital signal processing solution for ac induction motor." Application Note BPRA043.
The investigation was performed according the High-tech Development Program project dedicated to development of frequency converters for control of AC induction motor fan drives of advanced energy-saving industrial ventilation systems.
When paired with an AC induction motor, the CFW11 variable frequency inverter offers an efficient motor/drive combination to significantly increase motor efficiency and double the motor life in applications requiring variable speed and constant torque.