Electric Arc

(redirected from Electrical arc)
Also found in: Dictionary, Thesaurus.
Related to Electrical arc: Voltaic arc, Arc discharge, arcing

electric arc

[i¦lek·trik ′ärk]
(electricity)
A discharge of electricity through a gas, normally characterized by a voltage drop approximately equal to the ionization potential of the gas. Also known as arc.

Arc, Electric

 

(also called voltaic arc), one kind of self-maintaining arc discharge in a gas, in which the discharge phenomena are concentrated in a narrow, brightly glowing column of plasma. If the electrodes are horizontal, the column becomes arc-shaped under the influence of the upward currents of hot gas heated by the discharge.

An electric arc between two carbon electrodes in air was first observed (1802) and described (1803) by the Russian scientist V. V. Petrov and the English scientist H. Davy (1808–09), who called it a voltaic arc. Papers by the Russian scientists N. N. Benardos (welding with carbon electrodes, 1882, and AC welding) and N. G. Slavianov (welding with metal electrodes, 1888–91) were devoted to the development of the theory of the electric arc and the study of problems of its use in industry.

An electric arc can exist in any gas at near-atmospheric and higher pressures. At atmospheric pressure and a current strength of several amperes (amps), the plasma temperature in the column is about 5000°K; at high pressures and current strengths it is up to 12,000°K; and if the column is blasted with a powerful gas flow, the temperature reaches 50,000°K. The temperature distribution for various parts of an electric arc between carbon electrodes with a current of 200 amps is shown in Figure 1.

The magnetic field formed by the current of the electric arc interacts with the current, causing compression (constriction) of the column. With an increase in pressure in the surrounding medium, the current strength in the electric arc increases and the cross section of its column decreases. Near

Figure 1. Temperature distribution in various parts of the column of an electric arc

the electrodes the arc column is constricted even more, forming bright cathode and anode spots on their surfaces. The current density at the arc cathode depends on the cathode material and kind of gas and is usually 104-105 amps/cm2, but under specific conditions it can rise to 107 amps/cm2.

The current-voltage characteristic of an electric arc is a descending curve: a rise in current is accompanied by a drop in voltage between the electrodes.

Electric arcs are used in electrometallurgy (to make pure and refractory metals) and in lighting technology, and particularly extensively in electric welding. In some technical fields (for example, high-voltage technology), it is necessary to combat electric arc phenomena. Switches with various arc quenchers, including air, oil, and elegaz (sulfur hexafluoride) switches, and quenching by magnetic field are used to extinguish arcs that arise when high-voltage circuits are broken.

REFERENCES

Nikitin, V. P. “Russkaia shkola v razvitii elektricheskoi dugovoi svarki.” Avtogennoe delo, 1948, no. 7.
Somerville, J. M. Elektricheskaia duga. Moscow-Leningrad, 1962. (Translated from English.)
Butkevich, G. V. Dugovye protsessy pri kommutatsii elektricheskikh tsepei. Moscow, 1967.
References in periodicals archive ?
Using the obtained experimental data's and single phase equivalent circuit parameters, the current and voltage values of the electrical arc were calculated for 719-volt reference voltage.
The flash protection boundary, which is the approach limit distance from exposed live parts from which a worker could receive a second degree burn if an electrical arc flash occurred, and the PPE workers should wear when working within this boundary shall be accomplished by this analysis.
Shielded electrical arc and resistance welding methods have proved wonderfully adaptable to automation.
The source of light is a small arc tube made of quartz inside which an electrical arc is maintained.
CINCINNATI -- Every year, thousands of workers are involved in electrical arc accidents, molten metal splashes, flash fires and combustible dust explosions on the job.
Local power provider Energy Texas said a substation north of Port Arthur, which is located 90 miles (144 kilometers) east of Houston, shut down after an electrical arc was seen on Sunday morning.
A unique thermal damage pattern is that of metal erosion by electrical arc as shown in Figure 5.
An electrical arc can result in an explosive release of energy, which can cause injury to nearby personnel, and in extreme cases fatalities, damage to equipment and interruption to operations.
He went to their property and terrified them by firing the stun gun in their home, creating a blue electrical arc.

Full browser ?