(redirected from Rotor (turbine))
Also found in: Dictionary, Thesaurus.


rotary engine that uses a continuous stream of fluid (gas or liquid) to turn a shaft that can drive machinery.

A water, or hydraulic, turbine is used to drive electric generators in hydroelectric power stations. The first such station was built in Wisconsin in 1882. In a hydraulic turbine falling water strikes a series of blades or buckets attached around a shaft, causing the shaft to rotate, this motion in turn being used to drive the rotor of an electric generator. The three most common types of hydraulic turbine are the Pelton wheel, the Francis turbine, and the Kaplan turbine. Toward the end of the 19th cent. two engineers, Sir Charles A. Parsons of Great Britain and Carl G. P. de Laval of Sweden, were pioneers in the building of steam turbines. Continual improvements of their basic machines have caused steam turbines to become the principal power sources used to drive most large electric generators and the propellers of most large ships.

A steam turbine typically consists of a roughly conical, steel shell enclosing a central shaft along which a series of bladed disks are spaced like washers. The blades are curved and extend radially outward from the rim of each disk. In some steam turbines the shaft is surrounded by a drum to which the rows of blades are attached. Between each pair of disks is a row of stationary vanes attached to the steel shell and extending radially inward. Each set of stationary vanes and the bladed disk immediately next to it constitutes a stage of the turbine; most steam turbines are multistage engines.

At the inlet end of the turbine high-pressure steam enters from a boiler and moves through the turbine parallel to the shaft, first striking a row of stationary vanes that directs the steam against the first bladed disk at an optimum speed and angle. The steam then passes through the remaining stages, forcing the disks and the shaft to rotate. At one end of the turbine the shaft sticks out and can be attached to machinery. A large steam turbine unit may actually be composed of several turbines that are all using the same shaft and steam. Such a unit might consist of a small, high-pressure turbine, connected to a larger, intermediate-pressure turbine, connected to a still larger, low-pressure turbine. After the steam leaves the turbine, it is sent to a condenser where it is converted back into water before being returned to the boiler.

Gas turbines are used mainly as aircraft engines. Some are used to drive electric generators, as in a gas turbine–electric locomotive, and high-speed tools. The term gas turbine is usually applied to a unit whose essential components are a compressor, a combustion chamber, and a turbine that resembles a steam turbine. The turbine drives the compressor, which feeds high-pressure air into the combustion chamber; there it is mixed with a fuel and burned, providing high-pressure gases to drive the turbine, the gases expanding until their pressure drops to atmospheric pressure. In a turboprop engine the turbine is used to turn a propeller as well as the compressor. In a turbojet engine only a small pressure drop is used to drive the turbine, the majority of the pressure drop occurring as the gases are expelled directly out of the engine. A variation of the turbojet is known as the turbofan engine.

The Columbia Electronic Encyclopedia™ Copyright © 2013, Columbia University Press. Licensed from Columbia University Press. All rights reserved. www.cc.columbia.edu/cu/cup/
The following article is from The Great Soviet Encyclopedia (1979). It might be outdated or ideologically biased.



a prime mover characterized by purely rotational motion of the operating element—rotor—and a continuous process that changes the kinetic energy of a supplied working fluid—for example, steam, gas, or water—into mechanical energy.

Industrial steam and gas turbines are used to drive electric power generators (turbine generators), centrifugal compressors and blast blowers (turbocompressors and turboblowers), and feed, fuel, and oil pumps (turbine pumps). Steam and gas turbine engines are used as the main engines on ships. Gas turbines are also used as aircraft engines (turboprop and turbojet engines) and, in certain cases, in locomotives (gas-turbine locomotives) and special automobiles that require especially powerful engines. Hydroturbines are built only as industrial turbines for driving low-speed electric power generators (hydroelectric generators) in hydroelectric power plants.

As of 1976, the maximum power of turbines was 1,300 megawatts (MW) for steam turbines, 100 MW for gas turbines, and over 600 MW for hydroturbine units. Because of their economy, compactness, reliability, and possibility of achieving high unit power, turbines have practically replaced piston steam engines in present-day power engineering throughout the world. (See alsoGAS TURBINE, HYDROTURBINE, and STEAM TURBINE.)


The Great Soviet Encyclopedia, 3rd Edition (1970-1979). © 2010 The Gale Group, Inc. All rights reserved.


(mechanical engineering)
A fluid acceleration machine for generating rotary mechanical power from the energy in a stream of fluid.
McGraw-Hill Dictionary of Scientific & Technical Terms, 6E, Copyright © 2003 by The McGraw-Hill Companies, Inc.


A rotary wheel fitted with vanes, or buckets, radiating out form its circumference. The rotary wheel is activated by impulse or the reaction of fluid through the vanes, or blades, as the kinetic energy of fluids is converted into mechanical power.
An Illustrated Dictionary of Aviation Copyright © 2005 by The McGraw-Hill Companies, Inc. All rights reserved


any of various types of machine in which the kinetic energy of a moving fluid is converted into mechanical energy by causing a bladed rotor to rotate. The moving fluid may be water, steam, air, or combustion products of a fuel
Collins Discovery Encyclopedia, 1st edition © HarperCollins Publishers 2005