balance(redirected from protein balance)
Also found in: Dictionary, Thesaurus, Medical, Legal, Financial.
balance,instrument used in laboratories and pharmacies to measure the mass or weight of a body. A balance functions by measuring the force of gravity that the earth exerts on an object, i.e., its weight. Since the mass of an object is directly proportional to its weight, a balance can also be used to measure mass.
Types of Balances
The Equal-Arm Balance
The simplest type of balance, the equal-arm, or beam, balance, is an application of a leverlever,
simple machine consisting of a bar supported at some stationary point along its length and used to overcome resistance at a second point by application of force at a third point. The stationary point of a lever is known as its fulcrum.
..... Click the link for more information. . A uniform bar, the beam, is suspended at its exact center on a knife-edge set at right angles to it. The point of support is called the fulcrum. Two pans of equal weight are suspended from the beam, one at each end, at points equidistant from the fulcrum. Since the center of gravity of a uniform bar is at its midpoint, the beam supporting the pans will be in equilibrium, i.e., will balance on the knife-edge. A long pointer attached at right angles to the beam at the fulcrum indicates zero on a scale when the beam is at rest parallel to a level surface. It shows also the extent of swing of the beam on one side or the other, acting somewhat as a pendulum, when the beam is coming to rest. The object to be weighed is placed on one pan, and standard weights are added to the other until the balance of the beam is established again. The unknown weight can then be determined by adding up the standard weights in the pan.
The platform balance is a form of equal-arm balance in which two flat platforms are attached to the top side of the beam, one at each end. Such a balance has a rider, or weight, mounted on a bar that has a calibrated scale, is parallel to the beam, and connects the supports of the two platforms. This rider is moved along the bar, its edge marking decimal fractions of the unit weight.
The Unequal-Arm Balance
On the unequal-arm balance the beam is suspended at a point a very short distance from one of its ends. The object to be weighed is placed on this end, and a small known weight is moved out along the longer arm until balance is obtained. The unknown weight is then determined by using a formula involving the known weight and the distance of each weight from the fulcrum. One example of this type of balance is the steelyard, an ancient device still used in underdeveloped nations because of its portability and low cost; since the difference in length of the arms can multiply the effect of the smaller weight by a factor of 100 or more, a small steelyard hung from a tree can be used, for example, to weigh a side of beef.
The Spring Balance
A spring balance consists of a coiled spring fixed to a support at one end, with a hook at the other to which the body to be weighed is applied. Within the spring's limit of elasticity, the distance through which it is stretched is directly proportional to the weight of the applied body. A pointer and graduated scale attached to the spring convert this distance into a weight reading.
Accuracy of Balances
Although extremely accurate results can be obtained in measuring the weights of minute objects, it is physically impossible to construct any balance perfect enough to yield absolutely accurate determinations. For example, the analytical balance, a type of equal-arm balance, is used for delicate weighing in quantitative chemical analysis and in preparing pharmaceutical prescriptions; it must be kept in a glass case, since its accuracy is easily affected by dust and moisture. A spring balance does not retain its accuracy permanently, for no matter how carefully it is handled, the spring very gradually uncoils even though its limit of elasticity has not been exceeded.
For ordinary purposes the errors are so small that they are considered insignificant, but in chemical analysis it has been necessary to develop methods by which they can be further minimized. A so-called torsion balancetorsion balance,
instrument used to measure small forces. It is based on the principle that a wire or thread resists twisting with a force that is proportional to the stress.
..... Click the link for more information. , which depends on the twisting of a wire or thread, is employed for weighing, but the term is commonly used to indicate a device for measuring minute electrical and magnetic forces.
in weights and measures, instruments for determining weight, generally for other than laboratory use. For the principles of operation of all weighing devices, see balance.
..... Click the link for more information. .
(scales), an instrument for determining the weight of an object by the gravitational force acting upon it. Instruments for measuring other physical quantities, which are converted for this purpose to forces or force moments are sometimes called balances—for example, the electrodynamic balance and Coulomb’s balance.
The balance is one of the oldest of instruments. It originated and was perfected in connection with the development of trade, manufacturing, and science. The simplest balance, in the form of an equal-armed beam with suspended pans, was widely used in barter in ancient Babylon (2500 B.C.) and Egypt (2000 B.C.). The unequal-armed balance with a movable weight appeared somewhat later. As early as the fourth century B.C., Aristotle stated the theory of such balances (the rule of force moments). In the 12th century the Arab scholar Alhazen described a balance with scale pans whose error did not exceed 0.1 percent. It was used for determining the density of various substances, which made it possible to recognize alloys, expose counterfeit coins, distinguish precious stones from imitation stones, and so on. In 1586, Galileo constructed a special hydrostatic balance for determining the density of bodies. The general theory of the balance was developed by L. Euler in 1747.
The development of industry and transport led to the invention of balances for large loads. At the beginning of the 19th century a decimal balance with a weight-to-load ratio of 1:10 (Quintenz, 1818; see Figure 1) and a centesimal balance (T. Fairbanks, 1831) were built. At the turn of the 20th century, with the development of flow production, balances appeared for continuous weighing—conveyor balances, metering balances, and so on. Balances of the most varied construction began to be used in agriculture, industry, and in transportation for weighing solid products—in agriculture, grains, root crops, and eggs; in transportation, automobiles, railroad cars, and airplanes; and in industry, the tiniest components and units of precision-instrument manufacture and the multiton ingots of metallurgy. The construction of precision balances—the analytic balance, microanalytic balance,
Balances are classified according to purpose as standard balances (for checking balance weights), laboratory balances (including analytical balances), and general-purpose balances (used in various fields of science, technology, and the national economy). According to principle of operation, balances are divided into beam, spring, electrotensometric, hydrostatic, and hydraulic.
The most widely used balance is the beam balance. Its operation is based on the law of equilibrium of the lever. The fulcrum of the lever (the beam of the balance) may be in the middle (equal-armed balance) or shifted in relation to the middle (unequal-armed or one-armed balances). Many beam balances—for example, mercantile, automobile, and portion balances—consist of a combination of levers of the first and second orders. Knife edges or cushions of special steels or of hard stone (agate or corundum) usually serve as supports for the levers. On an equal-armed beam balance the object to be weighed is balanced by weights, but a certain excess (usually 0.05-0.1 percent) of the weights over the object (or vice versa) is compensated by the moment produced by the beam (with a pointer) because of displacement of its center of gravity relative to the initial position. The load, compensated by displacement of the beam’s center of gravity, is measured on a graduated scale. The value of a division s on the scale of a beam balance is determined by the formula
s = k (P0c/lg)
where P0 is the weight of the beam and its pointer, c is the distance between the beam’s center of gravity and the axis of its rotation, l is the length of the beam arm, g is free-fall acceleration, and k is a coefficient that is a function only of the resolving power of the reading device. The value of the division, and consequently the sensitivity of the balance as well, may be changed within definite limits (usually by moving a special small weight that changes the distance c).
In a number of laboratory beam balances a portion of the measured load is compensated by the force of electromagnetic interaction—by the attraction toward an immovable solenoid of an iron core connected to the arm of the beam. The strength of the current in the solenoid is regulated by an electronic device that brings the balance to equilibrium. By measuring the strength of the current, the load—which is proportional to it—can be determined. A similar type of balance is automatically brought to a position of equilibrium and is therefore generally used for measuring changing mass (for example, in research on processes of oxidation and condensation) when it is inconvenient or impossible to use an ordinary balance. The center of gravity of the beam in these balances coincides with the axis of rotation.
Balances, especially analytical balances, with built-in weights on a part of the load or on the whole load are coming into wider use in laboratory practice. The principle of operation of such balances was proposed by D. I. Mendeleev. Specially formed balance weights are suspended from the arm that has the balance pan (one-armed balance) or, less frequently, from the opposite arm. In one-armed balances (Figure 2), error caused by the inequality of the beam arms is completely eliminated.
Modern laboratory balances (analytical and other types) are equipped with a number of devices to increase the precision and speed of weighing—pneumatic or magnetic pan oscillation dampers, doors whose opening causes almost no air currents, heat shields, mechanisms for applying and removing the built-in balance weights, and automatic mechanisms for selection of built-in weights when equilibrating the balance. Projection scales that permit widening the range of measurements on the reading scale with small angles of deviation of the beam are used more and more frequently. All this makes it possible to significantly increase the speed of operation of the balance while preserving its precision.
In high-speed technical quadrant balances (Figure 3) the limit of measurements on the scale of the deviation of the beam is 50-100 percent of the maximum load of the balance (usually between 20 g and 10 kg). This is achieved by special construction of a heavy beam (quadrant) whose center of gravity is considerably lower than its axis of rotation.
Most types of metrological, standard, analytical, technical, mercantile, medical, wagon, and automobile balances—and also most automatic and portion balances—are built according to the principle of the beam balance.
The basis for the operation of spring and electrotensometric balances is Hooke’s law.
The sensitive element of the spring balance is a flat or cylindrical spiral spring that is deformed under the action of the weight of the body. The readings of the balance are shown on the scale, along which an indicator that is connected to the spring moves. It is assumed that the indicator will return to zero position after the load is removed; no residual deformation of the spring will occur because of the load.
Weight, rather than mass, is measured by the spring balance; however, in the majority of cases, the scale of the spring balance is graduated in units of mass. Since free-fall acceleration is a function of geographic latitude and altitude above sea level, the readings of the spring balance depend on its location. Moreover, the elastic properties of the spring depend on temperature and change with time; all this decreases the accuracy of spring balances.
In the torsion balance an elastic filament or spiral springs serve as the sensitive element. The load is determined by the angle of twist of the spring filament, which is proportional to the torsion moment produced by the load.
The operation of the electrotensometric balance is based on the conversion of the deformation of the resilient elements (columns, plates, or rings), which sense the force effects of the load, into a change in electrical resistance. Highly sensitive wire tensometers attached to the resilient elements serve as converters. As a rule, electrotensometric balances (wagon, automobile, crane, and other types) are used for weighing large loads.
Hydrostatic balances are used mainly to determine the densities of solid bodies and fluids. Their operation is based on Archimedes’ principle.
The hydraulic balance is analogous in arrangement to the hydraulic press. The results are read on a manometer graduated in units of mass.
All types of balances are characterized by (1) maximum load—the heaviest static load that they can tolerate without disruption of their metrological characteristics; (2) value of a scale division—the mass that corresponds to a change of one scale division in the reading; (3) maximum permissible error in weighing—the largest permissible difference between the result of one weighing and the actual weight of the weighed object; and (4) permissible reading variation—the greatest permissible difference in the readings of repeated weighings of the same body.
The weighing errors with maximum load of several types of balances are shown in Table 1.
|Table 1. Characteristics of various types of balances|
|1Using precision weighing methods|
|Maximum load||Weighing error with maximum load|
|Standard, first and second class...............||1-20kg||0.5-20mg1|
|Standard, third class; technical, first class...............||1-20kg||20-100mg|
|Analytic, semimicroanalytic, microanalytic, and assay...............||200g||0.1-1.0mg1|
REFERENCESRudo, N. M. Vesy: Teoriia, ustroistvo, regulirovka i poverka. Moscow-Leningrad, 1957.
Malikov, L. M., and N. A. Smirnova. “Analiticheskie elektricheskie vesy.” In Entsiklopediia izmerenii kontrolia i avtomatizatsii, issue 1. Moscow-Leningrad, 1962.
Orlov, S. P., and Avdeev, B. A. Vesovoe oborudovanie predpriiatii. Moscow, 1962.
Karpin, E. B. Raschet i konstruirovanie vesoizmeritel’nykh mekhanizmov i dozatorov. Moscow, 1963.
Gauzner, S. I., S. S. Mikhailovskii, and V. V. Orlov. Registriruiushchie ustroistva v avtomaticheskikh protsessakh vzveshivaniia. Moscow, 1966.
N. A. SMIRNOVA
(1) In bookkeeping, the difference between the totals for the debit and credit entries of an account. A debit balance, in which debits exceed credits, reflects the state of the given type of economic asset as of a certain date and is shown in the assets of the balance sheet. A credit balance, in which credits exceed debits, reflects the state of the sources of economic assets and is shown in the liabilities. The account is said to be closed if there is no balance.
(2) In foreign trade relations, the balance is the difference between the totals for exports and imports or between the totals for demands and obligations. An excess of exports over imports produces a positive foreign trade balance, whereas an excess of imports over exports produces a negative balance. In the balance of payments, a positive balance indicates that a country’s total receipts from other countries exceed the country’s payments to other countries. In a negative balance of payments, a country’s payments to other countries exceed a country’s receipts from other countries.